 |
 | Home | Contact Us | FAQ | Search & Site Map | Link to Us |
 | Sign In | Join | Other 45 Sites in Network |
| HomeDiscussion Groups General ModelsRailroadsRocketsRadio Controlled Air ModelsHelicoptersLand ModelsWater ModelsModelGeeks.com Contact UsLink To UsSearch & Site Map |
Model Forum / Radio Controlled / Air Models / September 2009Great Palnes Electra Conversion
I have come across an old GP Electra Glider kit. As you know it is pre- li-poly model and uses an old electric motor with a seven cell ni-cad. Can someone give me advice on what to replace the motor and battery with, plus anything else? > I have come across an old GP Electra Glider kit. As you know it is pre- > li-poly model and uses an old electric motor with a seven cell ni-cad. > Can someone give me advice on what to replace the motor and battery > with, plus anything else? I flew one with an Astro 05 and a 7cell nicad pack. It flew like a little pattern ship. The wing center section was glassed for extra strength, but no other mods. A really fun flyer. BobH I have one of these which I flew with a Master Airscrew 05 motor/gearbox turning a 12X8 folding prop. No speed controller, just an old Hitec On/Off remote switch. Full throttle or no throttle. recently flew it with a pair of 2S2500 mAh LiPo packs in parallel. Thought briefly of switching to brushless then figured, whets the point? Motor is only to get altitude for thermal searching and the can motor works fine. After all, it IS a glider. I will switch out the old on/off thingie for a proper LiPo capable speed controller but that it. Motor runs great at 7.4 volts and with the equivalent of 5 amps current. Side note: Goldberg makes the Electra, not Great Planes. I have had two; the first had a power disconnection on board which locked the servos into perfect trim to circle the field ON GLIDE going higher and higher and higher till it sailed over the hills and far away never to be seen again. Got to watch it fly away for a good half hour. Would have given my left nut for a rifle at that point... Dan AMA605992 >> I have come across an old GP Electra Glider kit. As you know it is pre- >> li-poly model and uses an old electric motor with a seven cell ni-cad. [quoted text clipped - 7 lines] > > BobH >I have come across an old GP Electra Glider kit. As you know it is pre- > li-poly model and uses an old electric motor with a seven cell ni-cad. > Can someone give me advice on what to replace the motor and battery > with, plus anything else? Definitely not something that will go over bridges or consume alcohol. . . > I have come across an old GP Electra Glider kit. As you know it is pre- > li-poly model and uses an old electric motor with a seven cell ni-cad. > Can someone give me advice on what to replace the motor and battery > with, plus anything else? You could weigh the current power system and put together something around a brushless that weighs the same. If you bias the system toward the smallest battery and biggest motor it'll go like a rocket; if you bias it toward a bigger battery it'll fly longer on a charge. Alternately, if you like how it flies you could go with a brushless motor with about 70-80% the rated power as your current motor -- motors are generally rated by their _input_ power, and brushless motors are generally more efficient than can motors, so this would give you _approximately_ the same power at the prop shaft. Then get the smallest LiPo that works (or ditto NiMH, if you can even get those any more). But if you do, you may find yourself putting a ton of ballast in the nose to get it all to balance -- making up the weight with motor would be much more fun.  Signaturehttp://www.wescottdesign.com |
Reply to this Message |
 Sign In
 Join
 My Latest Posts My Monitored Threads My Blog My Photo Gallery My Profile My Homepage Start New Thread Enable EMail Alerts Rate this Thread
|
©2012 Advenet LLC Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.